Q.Show that the electric field is always directed perpendicular to an equipotential surface.

Showing the 12 most recent of 15 on this concept.

1. CBSE 2026Set V11 markMCQ
   Q.The equipotential surfaces of an isolated point charge are :

   (a) Coaxial cylindrical surfaces

   (b) Plane surfaces parallel to each other

   (c) Concentric spherical surfaces centred at the charge

   (d) Spherical surfaces but not centred on the charge

   ›Reveal solutionSolution

   (c) Concentric spherical surfaces centred at the charge …

   🔒 Start your 14-day free trial to see the full solution →
2. CBSE 2026Set ANNUAL1 markMCQ
   Q.The angle between equipotential surface and electric field lines is

   (a) 180°

   (b) 90°

   (c) 45°

   (d) 0°

   ›Reveal solutionSolution

   Electric field lines are normal to equipotential surfaces everywhere, so the angle between them is always 90 degrees.

   An equipotential surface is one on which potential V is constant, so no work is done in moving a charge along it (W = q(V2-V1) = 0). If the field had any component along the surface, that component would do work in moving a charge along …

   🔒 Start your 14-day free trial to see the full solution →
3. CBSE 2026Set ANNUAL1 markMCQ
   Q.Equipotential surface at a large distance from a collection of charge whose total sum is not zero are –

   (a) ellipsoids

   (b) planes

   (c) paraboloids

   (d) spheres

   ›Reveal solutionSolution

   Far away, any localized charge distribution with nonzero total charge looks like a point charge.

   At a large distance from a collection of charges whose total (net) charge is not zero, the finer details of the actual charge distribution become negligible, and the distribution behaves effectively like a single point charge equal to the total charge, located roughly at its "centre". The equipotential surfaces of a point ch …

   🔒 Start your 14-day free trial to see the full solution →
4. CBSE 2026Set ANNUAL1 markMCQ
   Q.Which of the following statement is/are true for equipotential surface ?

   (a) The potential is different for different equipotential surfaces.

   (b) Electric field must always be normal to equipotential surface.

   (c) Work done to move a charge between any two points is zero.

   (d) All of the above

   ›Reveal solutionSolution

   All three listed statements about equipotential surfaces are individually true, so the correct choice is that all of the above hold.

   Working

   1. Different equipotential surfaces correspond to different potential values. By definition, each equipotential surface is the locus of points at one particular potential; a different surface (further/closer to the source) is at a different potential value.

   2. The electric field is always normal to an equipotential surface. If $\vec E$ had any component along the surface, it would do work moving a charge along that surface, changing its potential energy -- contradicting the surface being at constant potential. So $\vec E$ must be entirely perpendicular to it.

      …

   🔒 Start your 14-day free trial to see the full solution →
5. CBSE 2025Set X11 markMCQ
   Q.Equipotential surfaces for an isolated point charge are __________ in shape.

   (a) spherical

   (b) planar

   (c) cylindrical

   (d) conical

   ›Reveal solutionSolution

   (a) spherical. The potential of an isolated point charge is $V = \dfrac{1}{4\pi\varepsilon_0}\dfrac{q}{r}$, which has the same value at all points a distance $r$ from the charge. The locus of cons …

   🔒 Start your 14-day free trial to see the full solution →
6. CBSE 2025Set ANNUAL1 mark
   Q.Can two equipotential surfaces cross each other?

   ›Reveal solutionSolution

   If two equipotential surfaces intersected, the point of intersection would have to be at two different potentials at once, which is impossible; it would also mean the electric field has two directions at that point, which is equally impossible.

   Each equipotential surface is, by definition, a surface on which the electric potential has one single fixed value everywhere on it.

   If two equipotential surfaces at different potentials (say V1 and V2, with V1 not equal to V2) were to cross at some point P, then P would simultaneously have potential V1 (being on the first surface) and potential V2 (being on the second) - a contradiction, since a point can have only one value of potential.

   …

   🔒 Start your 14-day free trial to see the full solution →
7. CBSE 2025Set ANNUAL1 markMCQ
   Q.The angle between the electric lines of force and the equipotential surface is

   (a) 0°

   (b) 45°

   (c) 90°

   (d) 180°

   ›Reveal solutionSolution

   Electric field lines are always perpendicular to equipotential surfaces.

   An equipotential surface is one on which the potential V is the same everywhere, so moving along it does no work: $dV = -\vec{E}\cdot d\vec{l} = 0$ for any displacement $d\vec{l}$ on the surface. Since $\vec E$ is generally non-zero, this requires $\vec E \perp d\vec l$, i.e., the field (and hen …

   🔒 Start your 14-day free trial to see the full solution →
8. CBSE 2025Set ANNUAL1 mark
   Q.Figure below shows the equipotential surfaces for two charges q₁ and q₂. Identify the nature of charges q₁ and q₂.

   ›Reveal solutionSolution

   Only like charges give equipotential surfaces that merge into a single closed peanut/dumbbell-shaped surface enclosing both charges - unlike charges never do.

   For unlike (opposite-sign) charges, e.g. a dipole, the equipotential value $V=0$ occurs on the whole perpendicular-bisector plane between them, which is an open, unbounded surface, not a closed loop. Any closed equipotential surface for a non-zero potential value stays wrapped around one charge only - it can never merge with the loop of the other charge, because the sign of the potential contributed by the two charges is opposite.

   …

   🔒 Start your 14-day free trial to see the full solution →
9. CBSE 2024Set ANNUAL1 mark
   Q.Draw an equipotential surface for a positive charge (q > 0).

   ›Reveal solutionSolution

   For an isolated positive point charge, potential depends only on distance from the charge, so every surface of constant distance (a sphere centred on the charge) is an equipotential surface.

   The potential due to a point charge q at a distance r is:

   $V = \dfrac{1}{4\pi\varepsilon_0}\dfrac{q}{r}$

   Since V depends only on r, every point at the same distance r from the charge is at the same potential. So the equipotential surfaces are concentric spheres centred on the charge.

   …

   🔒 Start your 14-day free trial to see the full solution →
10. CBSE 2024Set ANNUAL1 markMCQ
    Q.A charge of 100 μC is placed at the centre of a circle of radius 5 m. Work done in moving a unit positive charge around the circumference of the circle once is

    (a) 500 J

    (b) 20 J

    (c) 0.05 J

    (d) 0 J.

    ›Reveal solutionSolution

    Work done by a conservative (electrostatic) field around any closed path is always zero — the charge returns to its starting point, so its potential energy is unchanged.

    The charge of 100 μC at the centre sets up a radially symmetric electric field. As the unit positive charge is carried once around the circumference, at every point on the circle the potential due to the central charge is the same, $V = kq/r$ (constant, since $r$ = 5 m throughout).

    …

    🔒 Start your 14-day free trial to see the full solution →
11. CBSE 2022Set ANNUAL1 mark
    Q.What is an equipotential surface?

    ›Reveal solutionSolution

    A surface where potential is constant everywhere; no work is done moving a charge along it.

    An equipotential surface is defined as a surface at every point of which the electric potential is the same. Since the potential does not change as we move from one point to another on such a surface, no work is done in moving a test charge along it ($W = q(V_A - V_B) = 0$ since $V_A = V_B$). This also means the electric field is always perpendicular to an equipotential surface at every point — if it had a component along the surface, work would be done moving a charge along that component, contradicting $V$ being constant. For a single …

    🔒 Start your 14-day free trial to see the full solution →
12. CBSE 2020Set ANNUAL1 mark
    Q.The angle between electric line of force and equipotential surface is ____. (Fill in the blank.)

    ›Reveal solutionSolution

    Electric field lines always cut equipotential surfaces at right angles (90°).

    An equipotential surface is one on which every point is at the same electric potential; no work is done in moving a charge along such a surface. Since the electric field $\vec{E} = -\nabla V$ points in the direction of the steepest decrease of potential, and there is no change in potential along an equipotential surface, the field must have zero component along the surface — i.e., it can only point perpendicular to it. If the field had any component along the sur …

    🔒 Start your 14-day free trial to see the full solution →