Which of the following electrodes will act as anodes, when connected to Standard Hydrogen Electrode? (Note: mo

NCERT Exemplar · Q16

Q. Which of the following electrodes will act as anodes, when connected to Standard Hydrogen Electrode? (Note: more than one of the given options may be correct.)

(i) Al/Al^3+ E⊖ = -1.66

(ii) Fe/Fe^2+ E⊖ = -0.44

(iii) Cu/Cu^2+ E⊖ = +0.34

(iv) F2(g)/2F^-(aq) E⊖ = +2.87

Odisha ChseMCQ· 1mImportance★★★★★

72% · 56/78 Questions

🔒 Locked · start free trial →

You're viewing a preview — the full solution, concept, methods & PYQ mapping are locked.

Start your 14-day free trial to unlock the full solution →

Concept understanding — Standard Electrode Potentials

Standard Electrode Potentials: A Number for "How Badly It Wants Electrons"

Dip a zinc rod into a zinc-salt solution and a tiny tug-of-war begins at the surface:

metal atoms tend to dissolve as ions (leaving electrons behind on the rod) while ions

from the solution tend to deposit as metal (consuming electrons). The rod ends up with

a characteristic electrical potential relative to the solution — the electrode potential. It is a direct measure of the tendency of that redox couple to gain or

lose electrons.

The Core Idea

Different couples pull electrons with very different strengths. Copper's ion grabs

them readily; zinc's barely wants them. Put a number on each couple and you can

predict, before mixing anything, who will oxidise whom.

Two conventions make the numbers comparable:

Standard conditions. Every species at unit concentration (1 M), any gas at 1 atm, temperature 298 K. The potential measured then is the standard electrode potential, written $E^\ominus$ .
A common zero. Potentials can only be measured as differences, so one electrode is defined as the reference: the standard hydrogen electrode (SHE), $2\text{H}^+ + 2e^- \rightarrow \text{H}_2$ , is fixed at exactly 0.00 V. Every $E^\ominus$ is the voltage of a couple measured against it.

By convention the values are tabulated for the reduction direction:

\text{Oxidised form} + ne^- \rightarrow \text{Reduced form} \qquad E^\ominus \text{ (in volts, at 298 K)}

Reading the Table

The standard-potential table (Table 7.1 in the Class 11 chapter) runs from

$\text{F}_2/\text{F}^-$ at $+2.87$ V down to $\text{Li}^+/\text{Li}$ at $-3.05$ V.

Two rules unlock it:

More positive $E^\ominus$ → stronger oxidising agent (the oxidised form is hungrier for electrons). F₂ tops the table; that is why fluorine oxidises almost everything.
More negative $E^\ominus$ → stronger reducing agent (the reduced form gives electrons up most easily). Li, K, Ca, Na at the bottom are the great electron donors. A negative $E^\ominus$ means the couple is a stronger reducing agent than the H⁺/H₂ couple; a positive one, weaker.

Predicting Whether a Reaction Goes

For any proposed redox reaction, the species being reduced acts as the cathode couple

and the species being oxidised as the anode couple:

E^\ominus_{\text{cell}} = E^\ominus_{\text{cathode}} - E^\ominus_{\text{anode}}

Worked feel: can Fe³⁺ oxidise iodide? $E^\ominus(\text{Fe}^{3+}/\text{Fe}^{2+}) = +0.77$ V is above $E^\ominus(\text{I}_2/\text{I}^-) = +0.54$ V, so

$E^\ominus_{\text{cell}} = +0.23$ V — yes. Can silver metal reduce Fe³⁺?

$0.77 - 0.80 = -0.03$ V — no.

This is also the logic of the activity series: a metal displaces, from solution, …

Why this formula?

Galvanic Corrosion: Why the Key Formulas Hold

Galvanic corrosion occurs when two dissimilar metals are electrically connected in the presence of an electrolyte. The key formula that governs this is the mixed potential theory, which leads to the galvanic current and corrosion rate expressions.

Let's build the reasoning step-by-step.

1. The Core Idea: Two Electrodes, One Circuit

When metals M₁ (more active, e.g., zinc) and M₂ (more noble, e.g., copper) are connected:

M₁ acts as the anode — it oxidizes (corrodes):

\text{M}_1 \rightarrow \text{M}_1^{n+} + n e^-

M₂ acts as the cathode — it reduces something (e.g., oxygen or H⁺):

\text{O}_2 + 2\text{H}_2\text{O} + 4e^- \rightarrow 4\text{OH}^- \quad \text{(in neutral/alkaline)}

2\text{H}^+ + 2e^- \rightarrow \text{H}_2 \quad \text{(in acidic)}

The two metals are electrically connected (via a wire or direct contact), and the electrolyte completes the circuit. Electrons flow from M₁ to M₂.

2. The Mixed Potential: Why It Exists

Each metal, when alone in the electrolyte, has its own open-circuit potential (OCP) — the equilibrium potential for its half-reaction. For M₁, it's $E_{\text{corr},1}$ ; for M₂, it's $E_{\text{corr},2}$ .

When connected, the system cannot stay at two different potentials. The entire metal couple must reach a single potential — the mixed potential $E_{\text{mix}}$ .

$E_{\text{mix}}$ lies between $E_{\text{corr},1}$ and $E_{\text{corr},2}$ .
At $E_{\text{mix}}$ , the total anodic current from M₁ equals the total cathodic current from M₂ (charge conservation):

I_{\text{anode}} = I_{\text{cathode}}

This is the fundamental equation of galvanic corrosion.

3. Deriving the Galvanic Current

Assume each electrode follows Butler-Volmer kinetics (for activation-controlled reactions). For the anode (M₁), the anodic current density $i_a$ at potential $E$ is:

i_a = i_{0,1} \exp\left( \frac{\alpha_a F (E - E_{0,1})}{RT} \right)

For the cathode (M₂), the cathodic current density $i_c$ is:

i_c = i_{0,2} \exp\left( -\frac{\alpha_c F (E - E_{0,2})}{RT} \right)

Where:

$i_{0,1}, i_{0,2}$ = exchange current densities
$\alpha_a, \alpha_c$ = transfer coefficients (typically ~0.5)
$F$ = Faraday constant
$R$ = gas constant
$T$ = temperature
$E_{0,1}, E_{0,2}$ = standard reduction potentials

At the mixed potential $E_{\text{mix}}$ :

I_{\text{galvanic}} = A_1 \cdot i_a(E_{\text{mix}}) = A_2 \cdot i_c(E_{\text{mix}})

Where $A_1$ and $A_2$ are the surface areas of the anode and cathode.

Why this holds: The net current from the anode must exactly balance the net current consumed at the cathode — otherwise, charge would accumulate, which is impossible in a steady-state circuit.

4. The Corrosion Rate Formula

The corrosion rate (mass loss per time) of the anode is given by Faraday's law:

\text{Corrosion rate} = \frac{I_{\text{galvanic}} \cdot M}{n \cdot F \cdot \rho}

Where:

$M$ = molar mass of the anode metal
$n$ = number of electrons transferred per atom
$\rho$ = density of the metal
$F$ = Faraday constant (96,485 C/mol)

Why this holds: Each mole of metal oxidized releases $n$ moles of electrons. The total charge passed $Q = I_{\text{galvanic}} \cdot t$ corresponds to moles of metal lost:

\text{moles lost} = \frac{Q}{nF} = \frac{I_{\text{galvanic}} \cdot t}{nF}

Multiply by $M/\rho$ to get volume or thickness loss.

5. The Area Effect: Why It Matters

From the mixed potential equation:

A_1 \cdot i_a(E_{\text{mix}}) = A_2 \cdot i_c(E_{\text{mix}})

If the cathode area $A_2$ is large relative to the anode area $A_1$ , then $i_a(E_{\text{mix}})$ must be large to balance the current. This means:

Small anode + large cathode → severe galvanic corrosion (high current density on the anode). …

Start your 14-day free trial to unlock the full solution →

An electrode acts as an anode (oxidation) when its standard reduction potential is lower than that of the SHE (0.00 V). Here, Al/Al³⁺ and Fe/Fe²⁺ have negative potentials, so they will be anodes. The correct options are (i) and (ii).

The key to this question is understanding what "anode" means in an electrochemical cell. An anode is the electrode where oxidation occurs — electrons are lost. When you connect any electrode to the Standard Hydrogen Electrode (SHE), the SHE is always assigned a potential of exactly 0.00 V. The direction of electron flow depends on which half-cell has a stronger tendency to gain electrons (i.e., a higher reduction potential).

Think of standard reduction potentials as a "desire to be reduced" scale. A more positive value means the species wants to gain electrons strongly. A more negative value means the species prefers to lose electrons (be oxidised) instead. When you connect two half-cells, the one with the lower reduction potential will actually undergo oxidation — it will be the anode.

Let's apply this to each option.

Al/Al³⁺ (E° = –1.66 V)

This is very negative. Compared to SHE (0.00 V), Al³⁺ has a much weaker tendency to get reduced. So when connected, Al metal will oxidise to Al³⁺, releasing electrons. That makes it the anode.

Tip

A very negative E° means the metal is highly reactive — it wants to lose electrons easily. Such metals are always anodes when paired with SHE.
Fe/Fe²⁺ (E° = –0.44 V)

Still negative, though less so than Al. Fe²⁺ still has a weaker reduction tendency than H⁺ (SHE). So Fe will oxidise to Fe²⁺, acting as the anode.

Watch out

Don't confuse "less negative" with "positive." –0.44 V is still less than 0.00 V, so Fe is still the anode.
Cu/Cu²⁺ (E° = +0.34 V) …

Start your 14-day free trial to unlock the full solution →

←Previous questionQ15 — Identify the correct statements with reference to the given reaction P…→Next questionQ17 — The reaction Cl2(g) + 2OH^-(aq) → ClO^-(aq) + Cl^-(aq) + H2O(l) repres…

Q.Which of the following electrodes will act as anodes, when connected to Standard Hydrogen Electrode? (Note: more than one of the given options may be correct.)

🎓Unlock everything free for 14 days

Unlock everything free for 14 days