Streamline flow is more likely for liquids with (Note: more than one of the given options may be correct.) (a)

NCERT Exemplar · Q10

Q. Streamline flow is more likely for liquids with (Note: more than one of the given options may be correct.)

(a) high density.

(b) high viscosity.

(d) low viscosity.

Odisha ChseMCQ· 1mImportance★★★★★est

75% · 40/53 Questions

🔒 Locked · start free trial →

You're viewing a preview — the full solution, concept, methods & PYQ mapping are locked.

Start your 14-day free trial to unlock the full solution →

Concept understanding — Reynolds Number

The Intuition: Why Does Flow Change Character?

Imagine you're pouring honey from a jar. It comes out as a smooth, steady, thick ribbon — you can almost see the layers sliding past each other without mixing. Now imagine turning on a tap fully. The water comes out fast, and the stream looks rough, chaotic, with eddies and splashes. The honey is laminar; the water is turbulent.

What's different? Two things: the speed and the stickiness of the fluid. Honey is very viscous (sticky), so any disturbance gets damped out quickly — the fluid resists being pushed around. Water is much less viscous, so at high speed, tiny irregularities grow into swirls and chaos.

But speed alone isn't the whole story. A slow river can be turbulent if it's wide and deep; a fast capillary flow in a thin tube stays laminar. So the size of the flow matters too. And the density — how much mass the fluid carries — affects how hard it is to change its motion.

The Reynolds number is the single number that captures all of this in one shot.

The Precise Statement

The Reynolds number is defined as:

Re = \frac{\rho v d}{\eta}

where:

$\rho$ = density of the fluid (kg/m³)
$v$ = characteristic speed of the flow (m/s)
$d$ = characteristic length scale (m) — for a pipe, the diameter; for an aeroplane wing, the chord length
$\eta$ = dynamic viscosity of the fluid (Pa·s)

It is dimensionless — every unit cancels out. That means it's a pure number, independent of whether you measure in SI, CGS, or imperial.

What It Actually Tells You

The numerator $\rho v d$ represents inertial forces — the tendency of the fluid to keep moving, to swirl, to be chaotic. The denominator $\eta$ represents viscous forces — the tendency of the fluid to stick together and resist deformation.

When $Re$ is small (say, below about 2000 for a pipe), viscous forces dominate. Any disturbance gets damped out. The flow is smooth, layered, predictable — laminar.

When $Re$ is large (above about 4000 for a pipe), inertial forces dominate. Disturbances grow. The flow becomes chaotic, mixing, with eddies of many sizes — turbulent.

Between 2000 and 4000 is a transition zone where the flow is unstable and can flip either way depending on conditions.

Important

The critical Reynolds number (the value where flow turns turbulent) depends on geometry. For a pipe it's ~2000–4000. For flow past a sphere it's ~10. For a flat plate it's ~5×10⁵. Always check the geometry before applying a critical value.

Why It's So Powerful …

Start your 14-day free trial to unlock the full solution →

Streamline flow is favoured by high viscosity and low density — the correct options are (B) high viscosity and (C) low density.

The key to this question lies in the Reynolds number, a dimensionless quantity that tells you whether a fluid flow will be smooth (streamline/laminar) or chaotic (turbulent). The Reynolds number is defined as

Re = \frac{\rho v D}{\eta}

where $\rho$ is the fluid density, $v$ the flow speed, $D$ a characteristic length (like pipe diameter), and $\eta$ the dynamic viscosity.

A low Reynolds number means viscous forces dominate, and the flow stays orderly — streamline. A high Reynolds number means inertial forces dominate, and the flow becomes turbulent. So to promote streamline flow, you want $Re$ to be small.

Effect of density ( $\rho$ )

Density appears in the numerator. A low density reduces $Re$ , making streamline flow more likely. High density does the opposite — it increases $Re$ and pushes the flow toward turbulence. So (C) low density is correct; (A) high density is wrong.
Effect of viscosity ( $\eta$ )

Viscosity appears in the denominator. A high viscosity reduces $Re$ , favouring streamline flow. Low viscosity increases $Re$ and encourages turbulence. So (B) high viscosity is correct; (D) low viscosity is wrong. …

Start your 14-day free trial to unlock the full solution →

←Previous questionQ9 — With increase in temperature, the viscosity of (Note: more than one of…→Next questionQ11 — Is viscosity a vector?

Q.Streamline flow is more likely for liquids with (Note: more than one of the given options may be correct.)

🎓Unlock everything free for 14 days

Unlock everything free for 14 days