A metal plate is getting heated. It can be because (a) a direct current is passing through the plate. (b) it is placed in a time varying magnetic field. (c) it is placed in a space varying magnetic field, but does not vary with time. (d) a current (either direct or alternating) is passing through the plate.

A metal plate is getting heated. It can be because (a) a direct current is passing through the plate. (b) it i

NCERT Exemplar · Q28

Q. A metal plate is getting heated. It can be because

(a) a direct current is passing through the plate.

(b) it is placed in a time varying magnetic field.

(d) a current (either direct or alternating) is passing through the plate.

Gujarat GsebMCQ· 1mImportance★★★★★

92% · 46/50 Questions

🔒 Locked · start free trial →

You're viewing a preview — the full solution, concept, methods & PYQ mapping are locked.

Start your 14-day free trial to unlock the full solution →

Concept understanding — Electromagnetic Induction

Electromagnetic Induction

Electromagnetic induction is the phenomenon in which a changing magnetic flux through a circuit produces an electromotive force (emf) — and hence a current, if the circuit is closed. It is the single idea behind generators, transformers, inductors, and the entire AC power grid.

The Central Discovery

Michael Faraday found (1831) that a current is induced in a coil not when a magnet sits still near it, but only while the magnet moves — that is, only while the magnetic flux linked with the coil is changing. A steady magnet, however strong, induces nothing.

Magnetic Flux

The key quantity is magnetic flux $\Phi_B$ through a surface of area $A$ in a field $\vec{B}$ :

\Phi_B = \vec{B} \cdot \vec{A} = BA\cos\theta

where $\theta$ is the angle between $\vec{B}$ and the area's normal. Its SI unit is the weber (Wb), where $1\ \text{Wb} = 1\ \text{T}\cdot\text{m}^2$ .

Flux can change in three distinct ways, and any of them induces an emf:

the field strength $B$ changes,
the area $A$ of the loop changes,
the orientation $\theta$ changes (a coil rotating in a field — the basis of the generator).

Faraday's Law

The induced emf equals the negative rate of change of flux. For a coil of $N$ turns:

\mathcal{E} = -N\,\frac{d\Phi_B}{dt}

The faster the flux changes, the larger the emf. This is why a magnet dropped quickly through a coil gives a bigger deflection than one moved slowly.

Lenz's Law — the Minus Sign

The negative sign expresses Lenz's law: the induced current flows in the direction that opposes the change producing it. Push a magnet's north pole toward a coil, and the coil's near face becomes a north pole to repel it; pull it away, and the face becomes a south pole to attract it. This is simply energy conservation — you must do work against this opposition, and that work becomes the electrical energy of the induced current.

Motional emf

A special, very useful case: a conducting rod of length $l$ moving with speed $v$ perpendicular to a field $B$ sweeps out area and develops an emf

\mathcal{E} = Blv

Here the emf arises because the free charges in the rod experience a magnetic force $q\vec{v}\times\vec{B}$ , which drives them along the rod. …

Why this formula?

Electromagnetic Induction

Electromagnetic induction is the effect discovered by Faraday: a changing magnetic flux through a circuit drives an induced EMF (and hence a current). The key word is changing — a steady field, however strong, induces nothing.

Magnetic flux

Flux measures how many field lines thread a surface bounded by the loop:

\Phi_B = \int \vec{B} \cdot d\vec{A} = BA\cos\theta

It can change three ways: by changing $B$ , by changing the area $A$ , or by rotating the loop (changing $\theta$ ).

Faraday's law

The induced EMF equals the rate of change of flux:

\mathcal{E} = -\frac{d\Phi_B}{dt}

For a coil of $N$ turns, $\mathcal{E} = -N\,\dfrac{d\Phi_B}{dt}$ . The EMF depends on how fast the flux changes, not on the flux itself — a slow change gives a small EMF, a rapid change a large one.

Lenz's law — the minus sign …

Start your 14-day free trial to unlock the full solution →

A plate heats whenever a current dissipates energy in it ( $I^2R$ ) — from a direct or alternating conduction current, or from eddy currents induced by a time-varying magnetic field. A steady (only space-varying) field on a stationary plate induces nothing. Correct options: (a), (b), (d).

Concept understanding. Heating in a conductor is Joule heating: power $P=I^2R$ . So the plate heats whenever a current flows in it, whatever the source of that current.

Why (a) and (d): A direct current through the plate dissipates $I^2R$ and heats it (a). More generally, any conduction current — direct or alternating — does the same, so (d) is also true. …

Start your 14-day free trial to unlock the full solution →

Same / Similar Concept — real previous-year questions on the same or a closely similar concept, not this exact question.

Showing the 12 most recent of 19 on this concept.

GUJCET 2026Set x1 markMCQ
$Q. In an ideal step up transformer, the number of turns in primary coil and secondary coil are 100 and 200 respectively. If output current is found to be 5A, then input current will be ______. (A) 2.5 A (B) 100 A (C) 5.0 A (D) 10 A$
›Reveal solutionSolution

$I_p=I_s\,N_s/N_p = 5\times2 = 10$ A.

For an ideal transformer $\dfrac{I_p}{I_s}=\dfrac{N_s}{N_p}$ . With $N_p=100$ , $N_s=200$ , output (secondary) current $I_s=5$ A: …
Start your 14-day free trial to see the full solution →
GSEB Higher Secondary Certificate (HSC) Examination 2026Set ANNUAL1 markMCQ
$Q. A.C. generator converts ___.$
(a) mechanical energy into electrical energy
(b) mechanical energy into heat energy
(c) mechanical energy into light energy
(d) electrical energy into mechanical energy
›Reveal solutionSolution

An AC generator (alternator) converts the mechanical energy used to rotate its coil/armature into electrical energy, via electromagnetic induction.

A coil is mechanically rotated in a magnetic field (or a field is rotated past a stationary coil). The changing flux linkage induces an alternating emf (Faraday's law), which drives current in an external circuit. The mechanical work done to keep the coil turning against the magne …

Start your 14-day free trial to see the full solution →
GUJCET 2025Set 031 markMCQ
$r$
(a) magnetic field increasing at the rate of 0.3 T/s and in figure
(b) magnetic field decreasing at the rate of 0.2 T/s. The direction of current in ring
(a) and ring(b), when observe from top are ______. [FIGURE:
(a) a ring in a magnetic field directed into the page (crosses);
(b) a ring in a magnetic field directed out of the page (dots).] (A) Clockwise, Anticlockwise (B) Anticlockwise, Anticlockwise (C) Clockwise, Clockwise (D) Anticlockwise, Clockwise
›Reveal solutionSolution
[!TLDR] Ring (a): into-page flux increasing -> induced current opposes it by making an out-of-page field -> anticlockwise. Ring (b): out-of-page flux decreasing -> induced current opposes by maintaining the out-of-page field -> anticlockwise. Both anticlockwise.

Apply Lenz's law, viewing each ring from the top (the reader's side), where x = into page (away from viewer) and . = out of page (toward viewer).

Ring (a): The field is into the page (x) and increasing, so into-page flux is growing. The induced current opposes this change and must create a magnetic field OUT of the page inside the ring. By the right-hand rule, a current producing an out-of-page field flows anticlockwise (as seen from the top). …
Start your 14-day free trial to see the full solution →
GUJCET 2025Set 031 markMCQ
$\varepsilon = 0$
›Reveal solutionSolution
[!TLDR]

With $\varepsilon=\varepsilon_0\sin\omega t$ (zero at $t=0$ ), the emf is maximum at $t=\dfrac{\pi}{2\omega}$ — option (D).

Concept

In an AC generator the induced emf is sinusoidal. The condition $\varepsilon=0$ at $t=0$ selects the sine form:

$\varepsilon=\varepsilon_0\sin(\omega t).$ …
Start your 14-day free trial to see the full solution →
GUJCET 2024Set 131 markMCQ
$0.5\,\Omega$
›Reveal solutionSolution

Induced $I=\dfrac{\Delta\Phi}{R\,\Delta t}$ , with the NE field making $45^\circ$ to the loop's normal.

Concept. EMF $=\dfrac{\Delta\Phi}{\Delta t}$ ; the normal to the east–west vertical plane points N–S, so a NE field makes $45^\circ$ with it.

Area $A=(0.10)^2=0.01\,\text{m}^2$ .

$\Phi_i=BA\cos45^\circ=0.10\times0.01\times0.707=7.07\times10^{-4}\,\text{Wb}$ , $\Phi_f=0$ . …
Start your 14-day free trial to see the full solution →
GUJCET 2024Set 131 markMCQ
$Q. If the primary coil of a transformer has 100 turns and the secondary has 200 turns. Then for a input of 220 V at 10 A find output current, in step up transformer. (A) 5.0 A (B) 50.0 A (C) 0.5 A (D) 0.05 A$
›Reveal solutionSolution

Ideal transformer: $I_s/I_p=N_p/N_s$ (current steps down when voltage steps up).

Concept. Power conserved $\Rightarrow V_pI_p=V_sI_s$ and $\dfrac{N_s}{N_p}=\dfrac{V_s}{V_p}=\dfrac{I_p}{I_s}$ . …
Start your 14-day free trial to see the full solution →
GUJCET 2023Set 091 markMCQ
$v$
›Reveal solutionSolution
[!TLDR] The approaching N pole makes the coil's near face a North pole (Lenz's law); its far face - the one the R.H.S. observer sees - is therefore a South pole, which appears as a clockwise current.

The magnet's N pole moves toward the coil, so the coil flux directed away from the magnet increases. By Lenz's law the induced current opposes this change, so the coil's face nearest the magnet (its left face) becomes a North pole to repel the incoming N pole. Consequently the coil's opposite face - the right-hand face, which the observer on the R.H.S. is looking at - behaves as a South pole. For an observer facing a magnetic South pole of a current loop, the induced current circulates clockwise (the loop's magnetic moment points toward the m …
Start your 14-day free trial to see the full solution →
GUJCET 2023Set 091 markMCQ
$cm^2$
›Reveal solutionSolution
[!TLDR]

$q=N\,BA/R = 1.2$ mC (time is irrelevant); option (C).

Concept

When flux through a coil changes, the charge that flows is
$q=\int i\,dt=\frac{N\,\Delta\Phi}{R},$
which depends only on the total flux change and resistance, not on how fast it happens. Here $\Delta\Phi = B A$ (flux goes from $BA$ to $0$ ).

Solution

Data: $N=10$ , $B=3$ T, $A=2\ \text{cm}^2=2\times10^{-4}\ \text{m}^2$ , $R=5\,\Omega$ .

$q=\frac{N\,B\,A}{R}=\frac{10\times3\times2\times10^{-4}}{5}=\frac{6\times10^{-3}}{5}\times10=\ ...$ …
Start your 14-day free trial to see the full solution →
GSEB Higher Secondary Certificate (HSC) Examination 2023Set ANNUAL1 markMCQ
$Q. A square of side L meter lies in the x-y plane in a region where the magnetic field is given by B (vector) = B_0 (2 i + 4 j + 3 k) T, where B_0 is constant. The magnitude of flux passing through the square is ___.$
(a) 4 B_0 L^2 Wb
(b) 3 B_0 L^2 Wb
(c) 2 B_0 L^2 Wb
(d) sqrt(29) B_0 L^2 Wb
›Reveal solutionSolution

The square lies in the x-y plane, so its area vector is along z; only the k-component (3 B_0) of B contributes: flux = 3 B_0 L^2.

The square (side L) lies in the x-y plane, so its area vector is A = L^2 k-hat (along z).

…

Start your 14-day free trial to see the full solution →
GSEB Higher Secondary Certificate (HSC) Examination 2023Set ANNUAL1 markMCQ
$Q. Magnetic flux linked with the coil is given by phi(t) = (2t^2 + 2t + 1) Wb and its resistance is 10 ohm. The current passing through the coil at t = 2 s is ___ A.$
(a) 1.5
(b) 1
(c) 0.5
(d) 2
›Reveal solutionSolution

Induced emf = -dphi/dt = -(4t+2); at t = 2, magnitude = 10 V, giving I = 10/10 = 1 A.

Flux phi(t) = 2t^2 + 2t + 1. Induced emf:

e = -dphi/dt = -(4t + 2).

…

Start your 14-day free trial to see the full solution →
GUJCET 2022Set 171 markMCQ
$Q. "The polarity of induced emf is such that it tends to produce a current which opposes the change in magnetic flux that produced it." This statement is known as ________. (A) Faraday (B) Maxwell (C) Kirchhoff (D) Lenz$
›Reveal solutionSolution

The induced current opposing the change in flux that produced it is Lenz's law.

Concept: Lenz's law states that the polarity of the induced emf is such that the induced current opposes the change in magnetic …
Start your 14-day free trial to see the full solution →
GSEB Higher Secondary Certificate (HSC) Examination 2022Set ANNUAL1 markMCQ
$Q. A current-carrying coil with N turns and cross-sectional area A is placed in a uniform magnetic field of magnitude B such that its plane remains perpendicular to the magnetic field. If the number of turns of the coil is now doubled, the magnetic flux linked with it = ______.$
(a) N^2 B A
(b) N B A / 2
(c) N B A
(d) 2 N B A
›Reveal solutionSolution

Flux linkage scales directly with the number of turns; doubling N doubles the flux linked with the coil.

Magnetic flux through a single loop with plane perpendicular to B: $\Phi = BA$ (since normal is parallel to B, $\cos\theta=1$ ).

…

Start your 14-day free trial to see the full solution →

←Previous questionQ27 — A long solenoid S has n turns per metre, with diameter a. At the centr…→Next questionQ29 — An emf is produced in a coil, which is not connected to an external vo…

Q.A metal plate is getting heated. It can be because

Concept understanding — Electromagnetic Induction

Electromagnetic Induction

The Central Discovery

Magnetic Flux

Faraday's Law

Lenz's Law — the Minus Sign

Motional emf

Why this formula?

Electromagnetic Induction

Magnetic flux

Faraday's law

Lenz's law — the minus sign …

Method: Reasoning Pattern for "What Causes This Heating/Effect?" Multi-Select Questions

Steps

Concept

Concept

Solution

Q.A metal plate is getting heated. It can be because

🎓Unlock everything free for 14 days

Unlock everything free for 14 days